[ Pobierz całość w formacie PDF ]
.SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV.00www.cobra.itMAKEMERCEDESMOD.SPRINTERYEAR98 → PETROLDIESELXALARM/SIRENPosition the compact alarms and the sirens in the engine compartment, on the POSITIONsupport of the battery.Pass the cables through the original rubber sleeve located on the bulkhead that divides the engine compartment and the passenger’s compartment, near the battery.POWER SUPPLY+ 30: connect to the 4 mm2 RED/WHITE wire located in the fuse box.- 31: connect to the car body.IGNITION WIRE+ 15/54: connect to the 1,5 mm2 BLACK/VIOLET wire located in the wiring harness coming out of the steering column and going to the fuse box.DIRECTION INDICATORSConnect to the 1 mm2 BLACK/GREEN and BLACK/WHITE wires located in the wiring harness that from the lights switch goes towards the fuse box on the left side, under the dashboard, driver’s side.ELECTRIC WINDOWSPositive control signalFront window, driver’s side:cut the 2 mm2 BLUE wire.Front window, passenger’s side: cut the 2 mm2 BLUE wire.The connections should be made directly in the wiring harnesses coming out of the respective original switches that are in the central part of the dash board, near the presetting of the car radio.CENTRAL DOORS LOCKING Additional motor We suggest to follow the diagram nr.35 to connect the central doors locking for the Bridge serie antithefts or the diagram nr.35A for the 3100 serie antithefts.In the 1998 version: the BLUE/RED wire (unlock) and the WHITE/RED wire (lock) should be cut.IMMOBILISATION POINT 1Gasoil pumpCut the 1 mm2 BROWN/BLACK wire located in the wiring harness of the brown connector of the black relay fixed to the plastic panel on the left of the bearing base of the driver’s side seat.IMMOBILISATION POINT 2Electrovalve control signalCut the 1,5 mm2 BLUE/BLACK wire located in the wiring harness coming out of the electrovalve in the engine compartment.STARTER+ 50: Cut the YELLOW/BLACK wire located on the left side of the wiring harness, under the dashboard and going to the fuse box.BONNET SWITCHInstall an additional switch on the headlamp support plate.DOORS SWITCHConnect to the 1 mm2 BROWN/WHITE wire coming out of the front door switch, driver’s side.LATERAL HATCH SWITCHConnect to the 1 mm2 BROWN/WHITE wire coming out of the lateral hatch switch.Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed mespr98gbd.docas per the instructions given on the product installation manual.SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV.00www.cobra.itFITTING DIAGRAM N° 35Diagram to make the central door’s locking on MERCEDES SPRINTER(for serie Bridge antithefts)Relay ofRelay of+30lockingopeningFUSEVIOLET/ORANGEVioletYellow/BlackOrangeGrey/BlackWiring harness located on the coming out of the driver’s side doorBLUE/REDGREEN/BLACKMFor vehicles from oct.’97 on the GREEN/BLACK wire there isn’t but you’ll find the 0,5 mm2 BLACK wire (there are 2, pls check) Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed mespr98gbd.docas per the instructions given on the product installation manual.SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV.00www.cobra.itFITTING DIAGRAM N°35ADiagram to make the central door’s locking on MERCEDES SPRINTER(for serie 3100 antithefts)Relay ofRelay of+30lockingopeningFUSEVIOLET/WHITEORANGE/WHITEVioletYellow/BlackOrangeGrey/BlackWiring harness located on the coming out of the driver’s side doorBLUE/REDGREEN/BLACKMFor vehicles from oct.’97 on the GREEN/BLACK wire there isn’t but you’ll find the 0,5 mm2 BLACK wire (there are 2, pls check) Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed mespr98gbd.docas per the instructions given on the product installation manual [ Pobierz całość w formacie PDF ]

  • zanotowane.pl
  • doc.pisz.pl
  • pdf.pisz.pl
  • blondiii.htw.pl
  •  

     

    nclude("s/6.php") ?>